cancel
Showing results for 
Search instead for 
Did you mean: 
Reply
sl1mpshady
Blue Screen Again
Posts: 10
Registered: ‎04-26-2019
Location: PH
Views: 145
Message 1 of 2

IBM Flex System EN2092 1Gb Ethernet Scalable Switch EXT Ports

How do I enable EXT Ports 11-20. I Have 20 RJ45 External Ports but when I issue 

Router# show interface information

Only 10 EXT Ports:

Router#show interface information
Alias   Port Tag RMON Lrn Fld PVID     DESCRIPTION              VLAN(s)
             Trk              NVLAN
------- ---- --- ---- --- --- ------ -------------- -------------------------------
INTA1    1     n   d    e   e     1   INTA1          1
INTA2    2     n   d    e   e     1   INTA2          1
INTA3    3     n   d    e   e     1   INTA3          1
INTA4    4     n   d    e   e     1   INTA4          1
INTA5    5     n   d    e   e     1   INTA5          1
INTA6    6     n   d    e   e     1   INTA6          1
INTA7    7     n   d    e   e     1   INTA7          1
INTA8    8     n   d    e   e     1   INTA8          1
INTA9    9     n   d    e   e     1   INTA9          1
INTA10   10    n   d    e   e     1   INTA10         1
INTA11   11    n   d    e   e     1   INTA11         1
INTA12   12    n   d    e   e     1   INTA12         1
INTA13   13    n   d    e   e     1   INTA13         1
INTA14   14    n   d    e   e     1   INTA14         1
EXT1     29    n   d    e   e     1   EXT1           1
EXT2     30    n   d    e   e     1   EXT2           1
EXT3     31    n   d    e   e     1   EXT3           1
EXT4     32    n   d    e   e     1   EXT4           1
EXT5     33    n   d    e   e     1   EXT5           1
EXT6     34    n   d    e   e     1   EXT6           1
EXT7     35    n   d    e   e     1   EXT7           1
EXT8     36    n   d    e   e     1   EXT8           1
EXT9     37    n   d    e   e     1   EXT9           1
EXT10    38    n   d    e   e     1   EXT10          1
MGT1     53    y   d    e   e  4095   MGT1           4095

* = PVID/Native-VLAN is tagged.
# = PVID is ingress tagged.
Trk  = Trunk mode
NVLAN = Native-VLAN

 

This is my switch 

IBM Flex System EN2092 1Gb Ethernet Scalable Switch.

System Information at 02:30:18 Wed May  1, 2019
Time zone: No timezone configured
Daylight Savings Time Status: Disabled

IBM Flex System EN2092 1Gb Ethernet Scalable Switch

Switch has been up for 0 days, 1 hour, 5 minutes and 51 seconds.
Last boot: 01:27:09 Wed May  1, 2019 (power cycle)

MAC address: a4:8c:db:f4:6e:00    IP (If 1) address: 0.0.0.0
Management Port MAC Address: a4:8c:db:f4:6e:ef
Management Port IP Address (if 128): 192.168.16.4
Software Version 7.8.22 (FLASH image2), active configuration.
Boot kernel version 7.8.22



Hardware Part Number        : 49Y4295
Hardware Revision           : 00
Serial Number               : Y01CCM86NC09
Manufacturing Date (WWYY)   : 2518
PCBA Part Number            : BAC-00079-00
PCBA Revision               : 0
PCBA Number                 : 00
Board Revision              : 00
PLD Firmware Version        : 1.6

Temperature Warning         : 26 C (Warning  at 63 C / Recover at 58 C)
Temperature Shutdown        : 26 C (Shutdown at 69 C / Recover at 64 C)
Temperature Inlet           : 20 C
Temperature Exhaust         : 27 C
Temperature Local           : 25 C
Temperature Remote 1        : 33 C
Temperature Remote 2        : 32 C
Temperature Remote 3        : 28 C
Temperature Phy 0x01        : 36 C
Temperature Phy 0x09        : 35 C
Temperature Phy 0x11        : 32 C

Power Consumption           : 26.800 W (12.244 V   2.175 A)

 

 

Highlighted
Lenovo Employee JVOSS2
Lenovo Employee
Posts: 225
Registered: ‎07-17-2018
Location: US
Views: 117
Message 2 of 2

Re: IBM Flex System EN2092 1Gb Ethernet Scalable Switch EXT Ports

Hello sl1mpshady,

 

The flex switches require a FOD (license) to fully utilize all the ports, both internal and external. You can check what FODs are installed using the "show software-key" command. Once the FOD is applied the ports will become available.

 

 

Check out current deals!


Shop current deals

Top Kudoed Posts